| Availability: | |||||||||
|---|---|---|---|---|---|---|---|---|---|
| Custom Square Washers are flat, square-profile metal washers with a central round hole. Their straight outer edges can suit assemblies that need a defined contact area, fit within a square envelope, or require an alternative to a round washer. Hardware-SP supplies drawing-defined square washers for OEM projects, reviewing side length, hole size, thickness, material, edge condition, finish, inspection, and packing from a drawing, CAD model, or approved sample. | |||||||||
The supplied images show square washers in several overall sizes and with a central round hole. A square outer profile can provide a defined bearing footprint where a round washer leaves unused space or does not suit the surrounding component. Hardware-SP manufactures square washers to the actual assembly drawing, rather than assuming a catalog size. Upload Drawing for Quote with the mating fastener and installed condition.
Side length, central-hole diameter, thickness, corner condition, and flatness all affect the washer's fit. The hole must allow the required bolt, screw, or clearance condition, while the outside profile must sit within the available bearing area. Drawing-defined production is helpful when a project needs a non-standard proportion, an offset or special hole, a particular edge condition, or a controlled visible surface.
1) A square footprint can be matched to a rectangular or square bearing area.
2) Side length and thickness can be chosen around the joint stack and available space.
3) The central hole can be specified for the stated fastener, clearance, or locating need.
4) Material and finish can be selected around corrosion, appearance, conductivity, and compatibility with adjacent parts.
Final suitability depends on the complete assembly requirement.
A typical drawing-led route can include blanking the square outline, piercing the central hole, deburring, cleaning, and a specified finish. The selected route depends on material, thickness, geometry, quantity, edge requirement, and surface expectation. The process review should identify any burr-sensitive face, protected cosmetic surface, or datum that controls how the washer seats in the finished assembly.
The images show bright metallic examples, but material and coating should be selected from the operating environment and appearance requirement rather than from the photo alone. State exposure to moisture, chemicals, temperature, electrical contact, or visible handling. For a painted or plated mating surface, note whether scratch protection, color consistency, or packing separation is required so the delivered condition supports receiving and assembly.
If the design also includes slotted, shaped, or non-round variants, the Custom Washers product page shows the wider drawing-defined washer family.
Square washers may be used in brackets, frames, electrical equipment, machinery, mounting structures, fixtures, furniture hardware, and other OEM assemblies. They can spread load below a nut or bolt head, provide a defined interface, or support a compact layout near straight edges. Their value comes from the relationship between the washer and surrounding parts, so the RFQ should include the installation view as well as the flat profile.
For repeat flat-part programs, start the process comparison from Metal Stamping before selecting tooling or a production route.
Upload Drawing for Quote with a PDF or CAD file, sample where useful, requested material, quantity, finish, side length, hole diameter, thickness, tolerances, mating-fastener details, inspection needs, packing requirement, and destination. Also identify the critical bearing face and any cosmetic or protected surface. These inputs allow the quotation to reflect the real component condition and the intended manufacturing route.
Item | Project reference |
Geometry | Square outside profile with drawing-defined center hole |
Size | Custom side length, hole size, and thickness |
Material | Drawing-dependent |
Surface | Drawing-dependent custom options |
Inspection | Profile, hole, thickness, edge condition, and finish to drawing |
Order type | Prototype, trial batch, or repeat OEM production |
Packing | Drawing-dependent or customer-specified |
Provide a current drawing or CAD model, material and finish requirement, quantity, critical dimensions and tolerances, mating fastener or part details, inspection expectation, packing method, and shipment destination. A sample can be helpful where it clarifies the desired edge, surface, or received condition.
Yes. Provide the required side length, hole diameter, thickness, tolerance, and mating-part details.
Yes. State the hole diameter, shape, position, clearance need, and any edge requirement on the drawing.
Select material around the environment, strength need, appearance, conductivity, and compatibility with adjoining parts. Confirm it in the RFQ.
Send a drawing or sample with material, quantity, finish, dimensions, critical tolerances, inspection needs, packing, and destination.