| Availability: | |||||||||
|---|---|---|---|---|---|---|---|---|---|
| Custom Shaped Washers are non-standard flat metal washers made with drawing-defined outside profiles and hole shapes. The supplied examples include square, octagonal, oval, and slotted openings. Hardware-SP supplies custom washers for OEM assemblies, reviewing profile, inside opening, thickness, material, edge condition, finish, inspection, and packing from a drawing, CAD model, or sample. 1) Special shaped washers and irregular washers help when a standard round profile cannot fit the assembly. 2) Slotted washers and square hole washers can support adjustment or location around a mating part. 3) OEM stamped washers and non standard washers are supplied to the approved drawing rather than a catalog assumption. | |||||||||
The supplied images show why a standard round washer is not always enough. A square or octagonal outside profile, an oval slot, a square opening, or small locating notches can help a washer fit the actual surrounding component. Hardware-SP makes these parts to drawing so the profile and opening are defined around the mating fastener, panel, bracket, or housing. Upload Drawing for Quote to begin.
The outside shape can determine the available bearing area, orientation, clearance, or contact with a flat surface. The inside opening may provide fastener clearance, adjustment travel, anti-rotation, or location around a non-round feature. These requirements should be shown on the drawing with the installed orientation, because the profile alone does not establish how the part must perform in the assembly.
1) An outside profile can be matched to restricted assembly space.
2) A square, oval, or shaped opening can be defined around the required locating or adjustment function.
3) Thickness and edge condition can be controlled for the stack-up and contact surface.
4) Material and finish can be selected for corrosion, appearance, conductivity, or compatibility.
Final dimensions and acceptance criteria remain drawing-dependent.
A likely route includes blanking the outside profile, piercing or slotting the opening, deburring, cleaning, and any specified surface treatment. The correct sequence depends on the material, thickness, shape complexity, quantity, and edge requirement. Any feature that faces a visible surface or bears against a soft coating should be identified during the drawing review so finishing and packing protect that requirement.
Complex holes, notches, and non-round outlines should be quoted from the actual part rather than an assumed washer standard. For a broader process decision involving flat profiles and repeat production,
For related process choices, start with Metal Stamping provides the parent manufacturing context.
State whether the washer is used below a bolt head, under a nut, against a panel, or as a locating interface. The RFQ should identify burr-sensitive edges, cosmetic faces, masked areas, marking, and packing separation where relevant. When related screw selection affects the opening or bearing surface, the
For related process choices, start with Custom Screws page can help align the mating-fastener discussion.
Upload Drawing for Quote with a PDF, CAD model, or sample; material request; quantity; profile dimensions; hole or slot geometry; thickness; finish; critical tolerances; mating-part details; inspection needs; packing; and destination. This provides the information needed to quote the actual special washer rather than a substitute catalog shape.
For purchasing, an accurate drawing-led RFQ makes supplier quotations comparable because it identifies the actual profile, opening, material, finish, quantity, inspection, and delivery condition. For engineering, the installed orientation, mating fastener, bearing face, and critical edge or slot define whether the washer will locate and protect the joint as intended. Flag the features that cannot change after approval so they are treated as release requirements rather than assumptions.
Item | Project reference |
Geometry | Custom outer profile and custom opening |
Size | Drawing-defined profile, hole or slot, and thickness |
Material | Drawing-dependent |
Thread | Not applicable unless stated on drawing |
Surface | Drawing-dependent custom options |
Inspection | Profile, opening, thickness, edge condition, and finish to drawing |
Order type | Prototype, trial batch, or repeat OEM production |
Packing | Drawing-dependent or customer-specified |
Provide the latest drawing or CAD model, material and finish, quantity, critical dimensions, mating-fastener information, inspection requirement, packing method, and destination. Add an installation view where the special opening or outside profile controls location or orientation.
Yes. Square, oval, slotted, or other drawing-defined openings can be reviewed with the outside profile and thickness.
Yes. Identify their position, purpose, edge requirement, and the mating feature on the drawing.
Yes. State finish, scratch protection, cosmetic side, and packing requirements in the RFQ.
Send a drawing or sample with material, quantity, dimensions, finish, tolerances, mating parts, inspection, packing, and destination.
Send a drawing or sample with material, quantity, dimensions, finish, tolerance, inspection, packing, downstream use, and destination.